Racing Car Radiator Cap JR-CHEZHIBAO Automotive Parts
Step 1 - start
First, make sure your engine is cold.The high temperature engine
shows the high pressure of high pressure in the tank - and may burn
you when you open the cap.Cold water can also damage the high heat
Step 2 - clean the water tank
Water tank and accessories
Open and secure the hood to avoid accidental slip.Then, use your
resistance brush and soapy water to remove the dead insects and
debris collected on the tank grille.Be sure to scrub in the
direction of the radiator, not reverse, because the metal is
fragile and easy to bend.Once the grille has been cleaned, a gentle
flow of water is guided from the top of the grille to confirm that
all the debris has been cleared completely.
Although you only flush your water tank once every two years, it is
a good idea to clean the tank grid every 12,000 miles.
Step 3 - check the cap
The cap of the water tank is used as the lid of the tank, and the
coolant inside the pressurized water tank keeps the engine cool.The
coolant pressure depends on the engine and the pressure rating is
on the top of the lid itself.
A water tank cover consists of a coil of coil that stretches
between the top and the bottom of the metal.The tension between the
spring and the sealing rubber is the key to keep the lid under
pressure, so if it can be easily compressed, the tank cover should
be worn and should be replaced.Another phenomenon of replacing the
cover of the tank is any corrosion or drying of the sealing
rubber.Generally speaking, water tank cover should be changed at
least every two years. Therefore, when flushing water tank, you can
use it as part of routine business.Please remember that different
tank caps have different pressure ratings, so keep the ratings in
your vehicle records.
The water tank is mainly composed of radiator core, water pipe,
cooling air blade, upper water tank and lower water tank.Water tank
in the radiator, the pipes will be connected to the tank of water
tanks and radiator below, hot water by go up and downstream to the
lower tank into warm water, cooling air blade channel, by suction
fan and the relative wind speed when driving the car forward, make
a lot of cold air through the air hole, cooling water will flow
through the pipe of heat absorption, divergence in the atmosphere
|Name :JR Radiator Cap||Brand:JR|
|MOQ:5 Piece||Place Of Origin:China|
- Brand Name:JR
- Item Type:Tank Covers
- Model Name:Thermo Radiator Cap
- Item Weight:0.28kg
- Item Height:15inch
- Material Type:aluminum
- Model Year:2015
- Item Length:5inch
- Special Features:Thermo Radiator Cap
- Item Width:8inch
- Country of origin:china guangzhou
- Car Model:universa
1.It is not only to prevent water leakage in the water tank, but
the larger role is to adjust the pressure balance of the water tank
to maintain the water level balance of the water tank.
2.Change the d1-spec temperature safe water tank cover, which can
let you know the accurate water tank temperature without engine.
Silica gel material inner plug - increases heat resistance
temperature and increases the closeness of the lid of the water
Extremely High Quality aluminum Radiator cap.Its design is very
sporty and has been received a good.
There is three model at the picture,when you make an order,please
leave message to us,what bar you need?if there is no message under
the order,we will send any model what in stock
1.Positive Feedback is very important to us.if you are satisfied
with our service, please remeber to give a positive feedback.
2.Please contact us before leaving neutral or negative feedback,we
will try our best to solve the problems.
3.If you are not satisfied with our best to solve the
problems,please contanct us before leaving your feedback and we
will resolve the issue immediately.thank you very much.
High quality and Durable
·Easy to install,just remove your original one and install the new
IF YOU HAVE ANY QUESTION ,PLEASE CONTACT WITH US:
Tel: 13763398810(Mary Lee)